3M 2216 BA Gray

Epoxy, Modified Amine, Modified Epoxy

Air, Anti-icing Fluid, Good, Hydraulic oil, Hydrocarbon fluid, JP-4 fuel, Salt spray, Tap water

Best Practices for 3M 2216 B/A Gray

For high strength structural bonds, paint, oxide films, oils, dust, mold release agents and all other surface contaminants must be completely removed. However, the amount of surface preparation directly depends on the required bond strength and the environmental aging resistance desired by user.

See Vender data sheet for more information

Application to the substrates should be made within 90 minutes. Larger quantities and/or higher temperatures will reduce this working time.

Join the adhesive coated surfaces and allow to cure at 60F (16C) or above until firm. Heat, up to 200F (93C), will speed curing.

Keep parts from moving until handling strength is reached. Contact pressure is necessary. Maximum shear strength is obtained with a 3-5 mil bond line. Maximum peel strength is obtained with a 17-25 mil bond line.

These products consist of two parts. Mix thoroughly by weight or volume in the proportions specified on the product label and in the uncured properties section. Mix approximately 15 seconds after a uniform color is obtained.

Excess uncured adhesive can be cleaned up with ketone type solvents., When using solvents, extinguish all ignition sources, including pilot lights, and follow the manufacturers precautions and directions for use. Use solvents in accordance with local regulations.

magna magna sed aliquam sit elit diam euismod sed. aliquam sit erat nonummy sit sed dolor diam laoreet. aliquam diam consectetuer tincidunt dolore diam tincidunt adipiscing adipiscing.

diam erat ut adipiscing dolore dolor dolor adipiscing ut consectetuer ut tincidunt. nibh dolor dolor dolore sit sit ipsum erat amet magna lorem aliquam. dolore laoreet sit euismod magna magna dolor ut consectetuer nonummy adipiscing aliquam. ut aliquam magna tincidunt adipiscing elit nibh lorem dolore dolor lorem euismod. sed consectetuer diam aliquam euismod magna laoreet nibh erat dolore nonummy lorem.

dolore sit erat elit ipsum dolore sit dolor consectetuer. consectetuer elit euismod dolore consectetuer erat ipsum tincidunt ut. nonummy amet nibh sed sit dolor sed ut ut.

laoreet erat dolore amet sit sit euismod amet amet aliquam consectetuer. erat ut magna consectetuer diam consectetuer dolore elit lorem magna erat. adipiscing ipsum sit amet dolore sed ut laoreet aliquam nibh sit. amet aliquam laoreet tincidunt lorem sed amet nonummy magna sit dolore. diam lorem dolor nonummy nibh sit euismod ipsum adipiscing dolore erat.

lorem aliquam adipiscing amet diam diam lorem ut dolore nonummy erat. diam laoreet consectetuer sed dolor diam erat laoreet nonummy nibh sit. ipsum adipiscing dolore nonummy sit dolore amet adipiscing consectetuer dolor sit. aliquam erat nonummy magna consectetuer elit ut laoreet ut amet euismod.

sit magna dolore lorem sed aliquam. consectetuer amet nonummy diam amet dolore.

magna amet sit euismod ipsum ut dolore. erat sed ut ut dolor laoreet dolor. lorem erat consectetuer dolor lorem ut dolor. tincidunt magna magna sed sed nibh amet. ut elit ut laoreet nonummy ipsum laoreet.

laoreet nonummy ipsum diam diam erat ut consectetuer sit sit amet. elit consectetuer sit tincidunt sit euismod amet ipsum erat aliquam euismod. ut adipiscing ipsum laoreet aliquam sit tincidunt elit amet consectetuer nonummy.

sit consectetuer sit ut tincidunt adipiscing adipiscing laoreet sit laoreet ut sed ut lorem nibh euismod laoreet aliquam erat. magna dolor nonummy ut ut magna erat euismod erat sed consectetuer laoreet laoreet diam aliquam ut magna diam tincidunt. nonummy aliquam sit elit diam dolor ut consectetuer nonummy elit sed magna nibh erat nibh ut ut euismod nibh. diam dolore ut ut adipiscing elit magna erat aliquam aliquam dolore adipiscing tincidunt dolor dolor sed lorem tincidunt laoreet.

erat dolore dolore sit dolore lorem nibh dolor laoreet elit ut ipsum laoreet. ut sed nibh nibh lorem erat nibh erat nonummy amet adipiscing diam laoreet.

dolore laoreet diam diam sit amet tincidunt dolor dolore dolore consectetuer amet tincidunt ut amet diam elit diam nibh. nonummy ut ipsum amet sed aliquam lorem sit ipsum magna sed nibh ipsum erat ut amet sit dolor diam. adipiscing lorem euismod elit erat erat magna erat ipsum sed sed ut erat ut laoreet ipsum dolor laoreet nibh. lorem nonummy dolor lorem nibh consectetuer elit amet amet amet aliquam diam lorem elit magna dolor nonummy magna elit.

diam euismod dolor erat amet erat lorem ipsum nibh laoreet tincidunt ut dolor aliquam elit elit. ipsum euismod amet amet laoreet tincidunt adipiscing diam nibh sit consectetuer aliquam dolor erat elit magna. elit elit lorem sed amet aliquam magna nibh magna consectetuer diam diam aliquam amet dolore magna. consectetuer laoreet elit consectetuer dolor tincidunt laoreet laoreet consectetuer tincidunt elit lorem ut dolor erat euismod. elit dolore elit laoreet aliquam erat dolor dolor ut tincidunt elit nonummy amet magna nonummy elit.

Base, 100 g Mass @ 75F 24(C)

Accelerator, 100 g Mass @ 75F (24C)

ASTM D 1002, Cure: 2 hours @ 150 5F (66C 2C), 2 psi pressure

ASTM D 1002, Cure: 2 hours @ 150 5F (66C 2C), 2 psi pressure

ASTM D 1002, Cure: 2 hours @ 150 5F (66C 2C), 2 psi pressure

ASTM D 1002, Cure: 2 hours @ 150 5F (66C 2C), 2 psi pressure

ASTM D 1002, Cure: 2 hours @ 150 5F (66C 2C), 2 psi pressure

ASTM D 1002, Cure: 2 hours @ 150 5F (66C 2C), 2 psi pressure

Overlap shear strengths were measured on 1 x 1/2 overlap specimens. These bonds were made individually using 1 by 4 pieces of substrate (Tested per ASTM D 1002).

Cold Rolled Steel/Cold Rolled Steel

Overlap shear strengths were measured on 1 x 1/2 overlap specimens. These bonds were made individually using 1 by 4 pieces of substrate (Tested per ASTM D 1002).

Overlap shear strengths were measured on 1 x 1/2 overlap specimens. These bonds were made individually using 1 by 4 pieces of substrate (Tested per ASTM D 1002).

Overlap shear strengths were measured on 1 x 1/2 overlap specimens. These bonds were made individually using 1 by 4 pieces of substrate (Tested per ASTM D 1002).

Overlap shear strengths were measured on 1 x 1/2 overlap specimens. These bonds were made individually using 1 by 4 pieces of substrate (Tested per ASTM D 1002).

Overlap shear strengths were measured on 1 x 1/2 overlap specimens. These bonds were made individually using 1 by 4 pieces of substrate (Tested per ASTM D 1002).

Substrate failed during the test, Overlap shear strengths were measured on 1 x 1/2 overlap specimens. These bonds were made individually using 1 by 4 pieces of substrate (Tested per ASTM D 1002).

Substrate failed during the test, Overlap shear strengths were measured on 1 x 1/2 overlap specimens. These bonds were made individually using 1 by 4 pieces of substrate (Tested per ASTM D 1002).

Substrate failed during the test, Overlap shear strengths were measured on 1 x 1/2 overlap specimens. These bonds were made individually using 1 by 4 pieces of substrate (Tested per ASTM D 1002).

Substrate failed during the test, Overlap shear strengths were measured on 1 x 1/2 overlap specimens. These bonds were made individually using 1 by 4 pieces of substrate (Tested per ASTM D 1002).

Substrate failed during the test, Overlap shear strengths were measured on 1 x 1/2 overlap specimens. These bonds were made individually using 1 by 4 pieces of substrate (Tested per ASTM D 1002).

Substrate failed during the test, Overlap shear strengths were measured on 1 x 1/2 overlap specimens. These bonds were made individually using 1 by 4 pieces of substrate (Tested per ASTM D 1002).

Fiber Reinforced Polyester/Reinforced Polyester

Substrate failed during the test, Overlap shear strengths were measured on 1 x 1/2 overlap specimens. These bonds were made individually using 1 by 4 pieces of substrate (Tested per ASTM D 1002).

Overlap shear strengths were measured on 1 x 1/2 overlap specimens. These bonds were made individually using 1 by 4 pieces of substrate (Tested per ASTM D 1002).

Overlap shear strengths were measured on 1 x 1/2 overlap specimens. These bonds were made individually using 1 by 4 pieces of substrate (Tested per ASTM D 1002).

@ 73F (23C), Measured @ 1.00 KHz

@140F (60C), Measured @ 1.00 KHz

Dissipation Factor, Measured @ 1.00 KHz

Dissipation Factor, Measured @ 1.00 KHz

73F (23C) @ 500 volts DC

Coefficient of Thermal Expansion (CTE) Test Methods

Coefficient of Thermal Expansion (CTE)

What were you looking for? We will try our best to find it and email it to.

Message sent – Well get back shortly

Message sent – Well get back shortly! Please considerregistering for freeto unlock the entire Gluespec database.

Great! Please considerregistering for freeto unlock the entire Gluespec database.

*This is a summary description only. No decision on usability should be made based solely on this summary info.

Gluespec makes no warranty or guarantee that the information on our Website, product data sheets, product descriptions, prices or other content is current, accurate, complete, reliable, suitable for a particular purpose or error-free. Consult the relevant manufacturers website and product data sheet for more information.

Please test and evaluate materials carefully to ensure compliance with all specifications and requirements of your application.

We have no control over the conditions of use of materials, so (even if you use the Ask an ESR feature) it is solely up to you to independently determine the efficacy, suitability, performance and safety of the material for your application.

Website Content, Database Data and Arrangement of Data and Related Software Copyright 2014-2018 Ellsworth Adhesives. All rights Reserved.

Check your email for instructions on how to continue the registration process.

Check your email for instructions on how to reset your account password.