Cast Epoxy and Polyurethane Components

Cartridge Systems – General Purpose

Triathane® Variable Hardness Polyurethane

New Epoxy and Polyurethane Developments

Cartridge Dispensed Epoxy and Polyurethane Systems

Ribbon Cast™ Polyurethane System for Roller Manufacturing

UL® Recognized Epoxy and Urethane Products

Two Component Heat Cured Epoxy Systems

UL® Recognized Epoxy and Urethane Products

New Epoxy and Polyurethane Developments

Cast Electrical and Mechanical Components

Maintenance, Restoration and Repair Materials

Safety Considerations using Urethane Products

Epoxy Flooring – Safe Handling Practices

Casting Method for Cast Coil and Instrument Transformers

Three Component variable hardness Polyurethane

How to evaluate Epoxy or Urethane products

How to remove cured Epoxy or Polyurethane

Procedure for Vacuum / Pressure Casting Fine Wire Coils

4 Reasons you have epoxy and polyurethane curing issues

Cast Electrical and Mechanical Components

Maintenance, Restoration and Repair Materials

Although most, if not all, suppliers of formulated Epoxy and Polyurethane materials manufacture products under vacuum. This being the case, there may still be some undesirable trapped gases that appear while using these compounds.

The following are some of the most common causes of bubbles:

Air inclusion during mixing the resin and hardener together.

Air trapped due to improper casting/moulding techniques.

Air introduced by suction as the material shrinks or due to a leaking tool.

Trapped residual solvent vapors from certain types of mould releases.

Volatile components being stripped out of the materials while casting under vacuum.

Gases generated during the reaction (hardening) process.

Gases formed during improper storage (moisture contamination etc.)

Gases introduced through pressurized systems.

Air from improperly de-aired resin and/or hardener.

The first and most important step in eliminating the problems caused by bubbles is simply taking care not to introduce air while handling the materials. If it is unavoidable to introduce air during mixing, such as during mixing by hand, it is highly desirable to remove the trapped gases under vacuum before using the mix. Gaseous bubbles trapped in a liquid, although initially microscopic in size, will expand when heated and can grow to become large enough to cause problems.

Polyurethane products are moisture sensitive. In fact they crave moisture and should not be mixed during days when the humidity is high. Urethane resins and hardeners should be protected from picking up moisture by applying a layer on Nitrogen on top of the material in the containers. Mixing urethane resin and hardener components together is best achieved under vacuum or at least under a blanket of Nitrogen.

Moisture contaminated polyurethane products will exhibit a large number of tiny bubbles on the surface or, in extreme cases, will rise to produce foam. These type of bubbles are next to impossible to remove.

As a rule, epoxy compounds are less moisture sensitive except for certain hardeners. Moisture contaminated epoxy hardeners can be usually recognized by the formation of a crust around the edges of the container. Moisture contaminated epoxy hardeners, depending on the formulation, will react faster than expected with the resin.

Bubbles tend to rise to the surface of the material and will, under ideal circumstances, given enough time, will eventually release from the liquid. In reality, most applications do not allow for the required time or the proper conditions for products to self de-air, vacuum must be applied to speed the removal of trapped gases from the mix.

The viscosity of the mix:The higher the viscosity the more difficult it is to remove gases.

The surface tension of the materials:Can be reduced by heating and the addition of surfactants

The temperature of the epoxy or urethane mix:Heating the material will reduce the viscosity. Be sure to consider the pot life and gel time before heating any mixed materials.

The amount of epoxy or urethane material being de-aired at one time:

The depth to surface ratio is important. The larger the surface that is exposed to the vacuum the better.

The lower the amount of product the rising bubbles have to travel through the better.

Agitation:Agitation (mixing) during the de-airing process (while under vacuum) will speed the removal of air considerably.

Thin film de-airing:The material is exposed to vacuum in a thin film. This is probably the best and fastest method of removing trapped gases.

Centrifugal force:Trapped gases may be forced out of the product by centrifugal forces by spinning at high speeds. This is not a widely practiced method and has limited possibilities in common applications.

Pressure:The application of pressure during the gellation process will reduce the size of the bubbles. The amount of pressure necessary will have to be determined by experimentation. Depending on the component configuration it is not uncommon to use 80 to 100 psi.

Vibration:Placing the mixture on a vibrating table will assist the bubbles in travelling to the surface.

Basic steps to produce bubble free epoxy or urethane castings:

Careful selection of the epoxy or urethane compound to be used.

The least number and amount of volatile ingredients.

The lowest possible viscosities (individual components and mixed)

De-air each component containing fillers individually.

Do not use violent motion during mixing and scrape the sides of the container to insure a thorough mix. De-gas the mixture under vacuum if possible.

If vacuum is not available, allow the mix to stand for a period of time to allow the coarse bubbles to escape prior to pouring (dont forget to consider the pot life).

Take precautions to minimize air entrapment while topping up the storage tanks. Slow, steady pouring into one spot will minimize air inclusion. De-air the materials in the storage tanks if possible.

Keep the fittings, valves and dispense pistons in good repair. Defective components will allow air to be sucked into the dispense lines.

Cavitations and lead/lag problems can be sources for air inclusions.

Pour slowly into one corner of the mould or container. Pouring slowly will allow the rising material to push the air ahead of it minimizing air entrapment.

Pour with the least amount of turbulence.

If possible, de-air the poured assembly prior to cure. This step is not necessary for parts involving small volumes. Large mass castings or castings with complicated shapes, conducive to air entrapment, should be de-aired prior to cure for best results.

Establish and use the appropriate temperatures that result in slow, even gellation. Provide a sufficient reservoir of cool material to replenish the shrinkage that takes place during gellation and cure.

Hydraulic hose fittings on vacuum lines allow for leak free connections and better vacuum.

29 Hg of vacuum is sufficient for most applications.

2 mm of vacuum has been found sufficient for high volume production.

Always use a large enough container to allow the material to rise under vacuum.

It may be helpful to add a drop or two of a suitable surfactant.

Almost all formulated epoxy and urethane materials contain at least some volatile ingredients. These ingredients are an essential part of the product and will start flashing off under vacuum. This is evidenced by the fact that the mix being de-aired never seems to be totally free of bubbles no matter how long it is vacuumed. Care should be taken not to vacuum strip the material. In most cases vacuum at 29 Hg for 5-10 minutes will sufficiently de-gas the mixture.

Casting Method for Cast Coil and Instrument Transformers

How to evaluate Epoxy or Urethane products

How to remove cured Epoxy or Polyurethane

Procedure for Vacuum / Pressure Casting Fine Wire Coils

4 Reasons you have epoxy and polyurethane curing issues

The above information is general in nature and is based solely on experiences byCrosslink Technology Inc.The recommendations provided herein may not be applicable in all situations. They are provided to the recipient as part of our customer service and the user must determine the relevance of the information to his/her application, considering any limitations that may be applicable thereto.Crosslink Technology Inc.does not accept any liability for direct or consequential damages resulting from the the implementations of these recommendations or the use of this information.

Toll free North America:1.800.563.3769

This email address is being protected from spambots. You need JavaScript enabled to view it.

We accept the following credit cards for Epoxy, Urethane, Transformer Bushings and Insulators orders meeting our minimum requirements: